As I referred to in my article on my home rack server project, I bought a 2U case to house my VM server.  I already had a smaller rack mount case, however it would only accept a mini-ITX board and I needed the case to support a MicroATX board.  This left me searching for something that was preferably around $100, would hold at least four drives, and that had reasonable air flow.  I also wanted it to be black so it would match the rest of my equipment as I am picky about esthetics.

Cutting right to the chase, I will say right off that the selection of decent cases suitable for a quiet home environment is next to nothing.  Further more almost every case I saw for under $200 was so badly designed that it actually made it  tough to decide since most cases this size will  only hold 3-4 drives.  Case builders that target the home or enthusiast put allot of time in the design, but case designers that make rack mounted stuff could care less about noise, or how easy it is to work on, much less the esthetics of he case.  After countless hours of searching I settled on the Ark 2U that at first glance looked like it might decent and it was less than $70.

One of the downsides of this case was that it was actually not black all the way around.  The face was black but rest was unpainted steel.  A trip to the local hardware store and I was able to fix that pretty quickly.  Gave it a few coats of some black paint and it was like it was bought that way.

 

http://www.newegg.com/Product/Product.aspx?Item=11-128-060

 

IMG_0674

 

Quieting the beast

As expected, the stock fans sounded like a jet engine.  A few minutes with Newegg and I found some SilentX and Enermax fans that had great airflow and very low noise (14-15 dba),  Though the case came with 4 fans I only installed 3 as that was more than enough to cool a low power VM server and if left me an easier way to route wires (another oversight from rackmount case designers).

 

IMG_0663IMG_0665IMG_0667IMG_0668IMG_0670

 

Drive cages

This case is actually spec’d at 6 x 3.5 drives and 2 x  5.25 inch drives.  In my case, I installed two of the WD Velociraptor and 2 SSDs in one of the two 3.5 inch cages, and 1 x 3.5 inch drive in the second cage.  This allowed me setup my 2 300Gig Raptors in a  RAID 0, 2 SSD RAID 1 (OS) and have room left over.  Final drive configuration is 2×300 in RAID 0 for VM speed, and 2 60 gig Intel SSD in a mirror configuration, and to complete the package, a 2T Caviar Black to back up the VM’s and the server.

 

IMG_0686IMG_0687IMG_0685IMG_0635IMG_0638IMG_0640IMG_0639IMG_0637

 

The Build

The build is pretty straightforward and consists of a Haswell i5-4570S (low power version), 32 gigs of DDR3, and an Asus Z87M-Plus as the motherboard.

IMG_0672IMG_0671IMG_0696IMG_0688IMG_0689IMG_0690IMG_0691IMG_0693IMG_0705IMG_0706IMG_0707IMG_0708IMG_0709

 

Summary

When all was said and done, I really like the end result though it was  painful to assemble.  Overall I found the case design to be decent (especially for $70),  It held a decent amount of drives, had good air flow, and it was very quiet once I replaced the turbine engines.  My only concern is that even though the case is pretty well designed, the build quality is a bit crude as it does not have the fit and finish that you might expect from a consumer case.  It has a ton of sharp edges indicative of poor build quality  and is a bit flimsy.  Doing things like removing drives requires removal of the card cage and incertain areas near the drives, it gets a bit cramped.    For the price, it is tough to go wrong with this if you need a server case, but just keep in mind that you will have to use some care when assembling you system and set asisde a couple bucks for some decent  fans that do not sound like an old refrigerator.

IMG_0712IMG_0713